Koupě Lupa - rady
Moderátor: Olaf87
- selkie
- VWexpert
- Příspěvky: 4943
- Registrován: 24.02.2006 21:02
- Bydliště: Praha
Koupě Lupa - rady
Zdar
pokukuju po nejakym malym aute pro manzelku...nedavno jsem nasel Lupo 1,2 TDI 3L, predem upozornuju, ze nemam zadny zkusenosti s timhle autem ani prevodovkou. Nyni k problemu. Majitel mi napsal, ze odpojil baterku, nechal ji nabit a po zapojeni mu prestala radit prevodovka (podle myho nazoru to nema souvislost, ale pisu, co napsal on me) a to tak, ze kdyz se pokusi dat zpatecku, tak to R zacne blikat a nezaradi se. Kdyz vypne motor, tak tam ty kvalty udajne jdou, ale jak nastartuje, tak se tam nezaradi. Moje otazky zni:
1. v cem konkretne je problem?
2. pujde to opravit?
3. za kolik?
4. byl by nekdo znaly ochoten se se mnou na nej jet podivat?
Diky za pripadny odpovedi
pokukuju po nejakym malym aute pro manzelku...nedavno jsem nasel Lupo 1,2 TDI 3L, predem upozornuju, ze nemam zadny zkusenosti s timhle autem ani prevodovkou. Nyni k problemu. Majitel mi napsal, ze odpojil baterku, nechal ji nabit a po zapojeni mu prestala radit prevodovka (podle myho nazoru to nema souvislost, ale pisu, co napsal on me) a to tak, ze kdyz se pokusi dat zpatecku, tak to R zacne blikat a nezaradi se. Kdyz vypne motor, tak tam ty kvalty udajne jdou, ale jak nastartuje, tak se tam nezaradi. Moje otazky zni:
1. v cem konkretne je problem?
2. pujde to opravit?
3. za kolik?
4. byl by nekdo znaly ochoten se se mnou na nej jet podivat?
Diky za pripadny odpovedi
Autoservis všech značek, troufnem si i na kamion.
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
Pokud to předtim řadilo a tu baterku měl odpojenou vic jak 24h tak to je jen otazka nastaveni řadiče. Takze pro toho kdo ma VAG tak no problem.
- selkie
- VWexpert
- Příspěvky: 4943
- Registrován: 24.02.2006 21:02
- Bydliště: Praha
Re: Koupe Lupa
no, predtim to udajne radilo...
prosim te, a problem to asi nebude pro nekoho, kdo ovlada nastaveni radice, predpokladam...v autorizaku to budou umet?
kazdopadne diky za radu
prosim te, a problem to asi nebude pro nekoho, kdo ovlada nastaveni radice, predpokladam...v autorizaku to budou umet?
kazdopadne diky za radu
Autoservis všech značek, troufnem si i na kamion.
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
Tak to te zklamu, ja kdyz koupil první 3L a pak odpojil baterku tak sem si taky myslel ze u VW mi to nastavi a to sem jim dones uz i navod na VAS jak to maji dělat a stejně to neudělali:-)
Napis odkud jsi nebo kde je to lupo, jestli by to nebylo daleko a vysel by mi cas tak by sem se zajel na to z tebou podivat. To nastaveni bychom připadně zrobili na mistě a hned by se vidělo jestli to jede nebo ne:-)
Napis odkud jsi nebo kde je to lupo, jestli by to nebylo daleko a vysel by mi cas tak by sem se zajel na to z tebou podivat. To nastaveni bychom připadně zrobili na mistě a hned by se vidělo jestli to jede nebo ne:-)
- selkie
- VWexpert
- Příspěvky: 4943
- Registrován: 24.02.2006 21:02
- Bydliště: Praha
Re: Koupe Lupa
no, to je pjekny teda, autorizovanej servis nevi
obavam se, ze na tebe je to pres celou republiku...je to az ve Varech
obavam se, ze na tebe je to pres celou republiku...je to az ve Varech
Autoservis všech značek, troufnem si i na kamion.
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
No to neni nic pro mně:) Teď mam dost starosti ve škole:-)
- selkie
- VWexpert
- Příspěvky: 4943
- Registrován: 24.02.2006 21:02
- Bydliště: Praha
Re: Koupe Lupa
a moh bys mi, prosim te, napsat, nebo poslat do sz, presnej postup jak to pres tu VAGinu nastavit?
Autoservis všech značek, troufnem si i na kamion.
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
Jop neni probelem:
5-Speed Electronic Manual Transmission (085)
Special Procedures
Prerequisites:
* Transmission Oil Level correct.
* No Fault Codes stored.
* Supply voltage at least 12V.
* Selector Lever in Tiptronic Mode.
* The following Basic Settings need to be carried out when:
o Every 30000 km / 19000 mi
o Engine has been removed/replaced
o Transmission has been removed/replaced
o Engine Control Module has been replaced
o Transmission Control Module has been replaced
o Clutch has been removed/adjusted/replaced
o Gear Selector or Actuator has been removed/adjusted/replaced
o Selector Lever has been removed/adjusted/replaced
* Common issues:
o The connection to the control module may be interrupted after starting the engine, as long as you do NOT switch of the ignition the cntrol module will continue at exactly the same position where the connection got interrupted. Step back into the basic setting as usual.
The following 3 Adaptations need to be carried out in a row!
Clutch Travel Sender Adaptation
[Select]
[02 - Transmission]
[Measuring Blocks - 08]
Block 002
[Go!]
Remove connector from hydraulic unit.
Check field 2, specification is 1.8...2.0 V.
If the specification is not reached, adjust the Clutch Travel Sender (G162).
Re-attach connector to hydraulic unit.
[Done, Go Back]
[Close Controller, Go Back - 06]
Cycle ignition OFF/ON.
[Select]
[02 - Transmission]
[Fault Codes - 08]
[Clear Codes - 05]
[Done, Go Back]
Gear Actuator Adaptation
[Basic Setting - 04]
Block 014
[Go!]
1st field should change from WAIT to ADJUST.
Loosen the gear actuator nut and tighten it with zero-potential.
Switch selector lever in E or D and back to Tiptronic Mode.
1st field should show WAIT now, tansmission now does some shifts, you can monitor them in field 2 (Range: 0...28).
1st field should change from WAIT to (-), pull the selector lever to Minus and hold it for 5 seconds.
1st field should show STOP now, put the selector lever in position STOP and wait 5 seconds.
1st field should show KickDown now, floor the accelerator pedal completely (to kick down) and wait 5 seconds.
1st field should show N now, put the selector lever in position N.
1st field should show StartMot now, start the engine and let it idle 15 seconds.
1st field should change from SEARCHNG to IGN.OFF, put the selector lever in Position STOP.
Switch ignition off and wait 15 seconds.
In case there is an Error during the Basic Setting, the Measuring Value Blocks (MVB) will show RTFM! followed by a Number which describes the Reason why it failed.
* 7 = Potentiometer 2 for Gear Recognition (G240)
o Check Switches and Wiring/Connectors using Measuring Value Blocks (MVB) and Wiring Diagram.
* 8 = Potentiometer 1 for Gear Recognition (G239)
o Check Switches and Wiring/Connectors using Measuring Value Blocks (MVB) and Wiring Diagram.
* 9 = Reverse Light Switch (F4)
o Check Switches and Wiring/Connectors using Measuring Value Blocks (MVB) and Wiring Diagram.
* 10 = Potentiometer Values fluctuating during Measurement
o Check the corresponding Potentiometers in Measuring Value Blocks (MVB) 015 to 018
o Check Fault Codes (repair if necessary) and Perform Basic Setting again
* 11 = Potentiometer Values
o Check the corresponding Potentiometers in Measuring Value Blocks (MVB) 015 to 018
o Check Fault Codes (repair if necessary) and Perform Basic Setting again
* 12 = Gear Actuator incorrectly adjusted or measured values out of specification.
o Potentiometer, Valves and Selector Finger at the Ball Heads for correct assembly and seating
o Perform Basic Setting again after adjusting the Gear Actuator
Creep Point Adaptation
[Select]
[02 - Transmission]
[Measuring Blocks - 08]
Block 025
[Go!]
Start the engine, engage the handbrake and press the foot brake.
Put the selector lever in position E or D.
You can determine the number of creep points left in field 3. It should start at 5 and count down to 0.
Release the brake pedal for at least 3 seconds, press the brake pedal again and hold it for at least 3 seconds.
Repeat the last step until field 3 shows 0.
If the specified value in field 3 is not reached, check fault codes and perform basic setting again.
[Done, Go Back]
[Close Controller, Go Back - 06]
Ve VIS-u je ten navod česky ale nelze to odtamtud skopirovat, takze bys si musel stahnout VIS. Ale myslim ze i podle toho to vpoho udelas:-)
5-Speed Electronic Manual Transmission (085)
Special Procedures
Prerequisites:
* Transmission Oil Level correct.
* No Fault Codes stored.
* Supply voltage at least 12V.
* Selector Lever in Tiptronic Mode.
* The following Basic Settings need to be carried out when:
o Every 30000 km / 19000 mi
o Engine has been removed/replaced
o Transmission has been removed/replaced
o Engine Control Module has been replaced
o Transmission Control Module has been replaced
o Clutch has been removed/adjusted/replaced
o Gear Selector or Actuator has been removed/adjusted/replaced
o Selector Lever has been removed/adjusted/replaced
* Common issues:
o The connection to the control module may be interrupted after starting the engine, as long as you do NOT switch of the ignition the cntrol module will continue at exactly the same position where the connection got interrupted. Step back into the basic setting as usual.
The following 3 Adaptations need to be carried out in a row!
Clutch Travel Sender Adaptation
[Select]
[02 - Transmission]
[Measuring Blocks - 08]
Block 002
[Go!]
Remove connector from hydraulic unit.
Check field 2, specification is 1.8...2.0 V.
If the specification is not reached, adjust the Clutch Travel Sender (G162).
Re-attach connector to hydraulic unit.
[Done, Go Back]
[Close Controller, Go Back - 06]
Cycle ignition OFF/ON.
[Select]
[02 - Transmission]
[Fault Codes - 08]
[Clear Codes - 05]
[Done, Go Back]
Gear Actuator Adaptation
[Basic Setting - 04]
Block 014
[Go!]
1st field should change from WAIT to ADJUST.
Loosen the gear actuator nut and tighten it with zero-potential.
Switch selector lever in E or D and back to Tiptronic Mode.
1st field should show WAIT now, tansmission now does some shifts, you can monitor them in field 2 (Range: 0...28).
1st field should change from WAIT to (-), pull the selector lever to Minus and hold it for 5 seconds.
1st field should show STOP now, put the selector lever in position STOP and wait 5 seconds.
1st field should show KickDown now, floor the accelerator pedal completely (to kick down) and wait 5 seconds.
1st field should show N now, put the selector lever in position N.
1st field should show StartMot now, start the engine and let it idle 15 seconds.
1st field should change from SEARCHNG to IGN.OFF, put the selector lever in Position STOP.
Switch ignition off and wait 15 seconds.
In case there is an Error during the Basic Setting, the Measuring Value Blocks (MVB) will show RTFM! followed by a Number which describes the Reason why it failed.
* 7 = Potentiometer 2 for Gear Recognition (G240)
o Check Switches and Wiring/Connectors using Measuring Value Blocks (MVB) and Wiring Diagram.
* 8 = Potentiometer 1 for Gear Recognition (G239)
o Check Switches and Wiring/Connectors using Measuring Value Blocks (MVB) and Wiring Diagram.
* 9 = Reverse Light Switch (F4)
o Check Switches and Wiring/Connectors using Measuring Value Blocks (MVB) and Wiring Diagram.
* 10 = Potentiometer Values fluctuating during Measurement
o Check the corresponding Potentiometers in Measuring Value Blocks (MVB) 015 to 018
o Check Fault Codes (repair if necessary) and Perform Basic Setting again
* 11 = Potentiometer Values
o Check the corresponding Potentiometers in Measuring Value Blocks (MVB) 015 to 018
o Check Fault Codes (repair if necessary) and Perform Basic Setting again
* 12 = Gear Actuator incorrectly adjusted or measured values out of specification.
o Potentiometer, Valves and Selector Finger at the Ball Heads for correct assembly and seating
o Perform Basic Setting again after adjusting the Gear Actuator
Creep Point Adaptation
[Select]
[02 - Transmission]
[Measuring Blocks - 08]
Block 025
[Go!]
Start the engine, engage the handbrake and press the foot brake.
Put the selector lever in position E or D.
You can determine the number of creep points left in field 3. It should start at 5 and count down to 0.
Release the brake pedal for at least 3 seconds, press the brake pedal again and hold it for at least 3 seconds.
Repeat the last step until field 3 shows 0.
If the specified value in field 3 is not reached, check fault codes and perform basic setting again.
[Done, Go Back]
[Close Controller, Go Back - 06]
Ve VIS-u je ten navod česky ale nelze to odtamtud skopirovat, takze bys si musel stahnout VIS. Ale myslim ze i podle toho to vpoho udelas:-)
- selkie
- VWexpert
- Příspěvky: 4943
- Registrován: 24.02.2006 21:02
- Bydliště: Praha
Re: Koupe Lupa
snad to kamos podle toho zvlade
kazdopadne diky za cas a ochotu
kazdopadne diky za cas a ochotu
Autoservis všech značek, troufnem si i na kamion.
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
Specializace na Bentley, Porsche
Odtah skoro zadarmo a pro klubáky ještě sleva 732 201 994
Tlučhuby:
- Marek 3L
- MILDA SM
- ppmajko
- Řidič
- Příspěvky: 52
- Registrován: 25.12.2007 10:08
- Bydliště: SK Poprad
Re: Koupe Lupa
no chalani ja to dens idem skusit,,,,auto radi v pohode len sem tam ked preradzuje tak trhne s autom ako keby clovek pustil rychlejsie spojku,,,asi to bude tym nastavenim,,,aspon dufam
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
Když ti škube třeba spojku doštelovat ale taky to děla když špatně tlakuje pumpa resp. tlakovy obvod rychle ztraci tlak....
- ppmajko
- Řidič
- Příspěvky: 52
- Registrován: 25.12.2007 10:08
- Bydliště: SK Poprad
Re: Koupe Lupa
da sa to repasovat? myslim ta pumpa,,,on aj rano ked idem startovat tak dost dlho tlaci
a ta spojka sa kde presne steluje?
dik
a ta spojka sa kde presne steluje?
dik
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
Tak spojka se nastavuje na spojkovem valečku a v tom navodu je postup jake máš mit hodnoty na VAG-u. Jinak nejprve bych zkusil pretesnit celou soustavu. je tam 7 O-kroužku ktere je třeba vyměnit a pak by to mělo byt ok. Ale mam kamarada na slovensku ktery to všechno přetěsnil už dvakrat a vždy 1 tyden auto tlakovalo super a pak zase dlouho. On kdyz ma maly tlak tak muže trochu škubat. Hlavně z 1 na 2:-)
- ppmajko
- Řidič
- Příspěvky: 52
- Registrován: 25.12.2007 10:08
- Bydliště: SK Poprad
Re: Koupe Lupa
presne to mi to sposobuje,,,pri 1do2 sem tam sklbne,,,ale co som pozeral tak za nejakych 60e sa da objednat cela sada na pretesnenie
- McMahon
- Pilot
- Příspěvky: 731
- Registrován: 19.05.2008 17:01
- Bydliště: Guty 74
- Kontaktovat uživatele:
Re: Koupe Lupa
Muzes poslat odkaz?