schema zapojeni autoradia

[jan.fort]

Ahoj vsem, chci se optat, nemel by jste tady nekdo schema k zapojeni RNS300.
Kamarad si ho koupil, ale nejak mu to blbne.Lze zapnout, kdyz klicek neni v zapalovani a leva strana mu hraje v pravo a naopak...Myslite, ze by to mohlo byt zpusobene prehozenim dratku nebo je v tom autoradiu neco spatne?

Predem moc dekuji....

[dream7000]

do akeho auta ho dal? a ma ho spravne nakodované?

[jan.fort]

Ma 3C sedana 2007, zkouseli jsme ho dat i do meho 2006 kombi a dela to to same...na iso konektoru je videt, ze tam s tim nekdo neco delal...nevim, jestli to bylo v jinem aute...

[tornado1]

radio jde vždy zapnout když není klíček v zapalování... po hodině se vypne.

[jan.fort]

Ale ono sviti i po vyndani klicku, to by nemelo, ne?...
Nemuze to vybit baterku?
Ono asi bude lepsi, kdyz se s tim zajede k autoelektrikarovi, nez se v tom hrabat...

[tornado1]

tak tam nejsou cany... dneska jedu do Prahy, ale nemám moc času.. můžu mrknout a říct co s tím je.... nebo mi to dovez do Humpolce a dám to do kupy

[jan.fort]

OK dohodnu se s tim kamaradem, ale on je ted mimo, udelal si prodlouzeny vikend...to se nekdo ma....Ozvu se po sz...Diky...

[dream7000]

asi ťa zaujíma toto...PARDON omylom som sem dal RNS 510
Multi-pin connector 1, 8-pin, for loudspeaker outputs

1 – Rear right loudspeaker, positive
2 – Front right loudspeaker, positive
3 – Front left loudspeaker, positive
4 – Rear left loudspeaker, positive
5 – Rear right loudspeaker, negative
6 – Front right loudspeaker, negative
7 – Front left loudspeaker, negative
8 – Rear left loudspeaker, negative

Multi-pin connector 2, 8-pin, for voltage supply lines and CAN bus

9 – CAN bus, high
10 – CAN bus, low
11 – Display voltage supply, positive, optional for radio module low version only
12 – Voltage supply, negative, terminal 31
13 – Display HV CAN bus low, optional for radio module low version only, not for midline
14 – Display HV CAN bus high, optional for radio module low version only, not for midline
15 – Voltage supply, positive, terminal 30
16 – Anti-theft coding control signal, SAFE, positive

Multi-pin connector 3, 12-pin, for telephone and microphone signals

1 – Microphone input, negative
2 – AUX output, audio, right
3 – AUX output, common signal earth
4 – Microphone output, negative
5 – Telephone audio input signal left, negative
6 – Telephone audio input signal right, negative
7 – Microphone input, positive
8 – AUX output, audio, left
9 – Microphone output, positive
10 – Telephone mute (mute switch for radio)
11 – Telephone audio input signal left, positive
12 – Telephone audio input signal right, positive

Multi-pin connector 4, 12-pin, for CD changer control and CD audio input signals

1 – AUX signal input, left
2 – AUX signal earth
3 – CD changer, audio signal earth
4 – CD changer, voltage supply, positive, terminal 30, contact continuous load greater than 1 A, temporary peak load 5 A
5 – Not assigned
6 – CD changer, DATA OUT (data exchange for CD changer control from radio navigation system to CD changer)
7 – AUX signal input, right
8 – CD changer, left audio channel, CD/L
9 – CD changer, right audio channel, CD/R
10 – CD changer, control line, switched positive
11 – CD changer, DATA IN (data exchange for CD changer control from CD changer to radio navigation system)
12 – CD changer, CLOCK (internal check protocol for data flow monitoring)

Multi-pin connector 5, audio and video, 26-pin


1 – Reserved for Debug RX protocol
2 – Reserved for Debug TX protocol
3 – Not assigned
4 – Video signal input, RGBS, negative (ground)
5 – Video signal output LF, Right (Audio use 17 for ground)
6 – Ground Sync input
(Internal universal preparation for mobile telephone, mobile telephone detection)
7 – Video signal output, vertical and horizontal synchronisation
(Internal universal preparation for mobile telephone, cradle and button evaluation)
8 – Video signal ouput, green
(Internal universal preparation for mobile telephone, cradle, aerial diagnosis)
9 – Video signal input, RGBS, negative (ground)
10 – Video signal input LF, right (Audio use 24 for ground)
11 – Video signal input, screening earth
12 – Video signal input, vertical and horizontal synchronisation
13 – Video signal input, green
14 – Not assigned
15 – Not assigned
16 – Not assigned
17 - Video signal output, LF, negative (ground)
18 – Video signal output LF, Left (Audio use 17 for ground)
19 – Video signal output, RGBS, negative (ground)
(Internal universal preparation for mobile telephone, cradle, negative)
20 – Video signal output, Blue
(Internal universal preparation for mobile telephone, switched terminal 30)
21 – Video signal output, Red
22 – Video signal input, LF, negative
23 – Video signal input, LF, left (Audio use 24 for ground)
24 – Video signal input, RGBS, negative (ground)
25 – Video signal input, blue
26 – Video signal input, red

Connectors 6, aerial connectors


1 – AM and FM2 radio reception aerial connector, double Fakra, no coding, impedance 50 ohms, colour cream-white

2 – FM1 radio reception aerial connector, double Fakra, coding B, impedance 50 ohms, colour cream-white

3 – Navigation aerial connector, double Fakra, coding C, impedance 50 ohms, colour signal blue

[jan.fort]

To je presne ono
Zlatej clovicek, moc dekuju

asi ťa zaujíma toto...PARDON omylom som sem dal RNS 510
Multi-pin connector 1, 8-pin, for loudspeaker outputs

1 – Rear right loudspeaker, positive
2 – Front right loudspeaker, positive
3 – Front left loudspeaker, positive
4 – Rear left loudspeaker, positive
5 – Rear right loudspeaker, negative
6 – Front right loudspeaker, negative
7 – Front left loudspeaker, negative
8 – Rear left loudspeaker, negative

Multi-pin connector 2, 8-pin, for voltage supply lines and CAN bus

9 – CAN bus, high
10 – CAN bus, low
11 – Display voltage supply, positive, optional for radio module low version only
12 – Voltage supply, negative, terminal 31
13 – Display HV CAN bus low, optional for radio module low version only, not for midline
14 – Display HV CAN bus high, optional for radio module low version only, not for midline
15 – Voltage supply, positive, terminal 30
16 – Anti-theft coding control signal, SAFE, positive

Multi-pin connector 3, 12-pin, for telephone and microphone signals

1 – Microphone input, negative
2 – AUX output, audio, right
3 – AUX output, common signal earth
4 – Microphone output, negative
5 – Telephone audio input signal left, negative
6 – Telephone audio input signal right, negative
7 – Microphone input, positive
8 – AUX output, audio, left
9 – Microphone output, positive
10 – Telephone mute (mute switch for radio)
11 – Telephone audio input signal left, positive
12 – Telephone audio input signal right, positive

Multi-pin connector 4, 12-pin, for CD changer control and CD audio input signals

1 – AUX signal input, left
2 – AUX signal earth
3 – CD changer, audio signal earth
4 – CD changer, voltage supply, positive, terminal 30, contact continuous load greater than 1 A, temporary peak load 5 A
5 – Not assigned
6 – CD changer, DATA OUT (data exchange for CD changer control from radio navigation system to CD changer)
7 – AUX signal input, right
8 – CD changer, left audio channel, CD/L
9 – CD changer, right audio channel, CD/R
10 – CD changer, control line, switched positive
11 – CD changer, DATA IN (data exchange for CD changer control from CD changer to radio navigation system)
12 – CD changer, CLOCK (internal check protocol for data flow monitoring)

Multi-pin connector 5, audio and video, 26-pin


1 – Reserved for Debug RX protocol
2 – Reserved for Debug TX protocol
3 – Not assigned
4 – Video signal input, RGBS, negative (ground)
5 – Video signal output LF, Right (Audio use 17 for ground)
6 – Ground Sync input
(Internal universal preparation for mobile telephone, mobile telephone detection)
7 – Video signal output, vertical and horizontal synchronisation
(Internal universal preparation for mobile telephone, cradle and button evaluation)
8 – Video signal ouput, green
(Internal universal preparation for mobile telephone, cradle, aerial diagnosis)
9 – Video signal input, RGBS, negative (ground)
10 – Video signal input LF, right (Audio use 24 for ground)
11 – Video signal input, screening earth
12 – Video signal input, vertical and horizontal synchronisation
13 – Video signal input, green
14 – Not assigned
15 – Not assigned
16 – Not assigned
17 - Video signal output, LF, negative (ground)
18 – Video signal output LF, Left (Audio use 17 for ground)
19 – Video signal output, RGBS, negative (ground)
(Internal universal preparation for mobile telephone, cradle, negative)
20 – Video signal output, Blue
(Internal universal preparation for mobile telephone, switched terminal 30)
21 – Video signal output, Red
22 – Video signal input, LF, negative
23 – Video signal input, LF, left (Audio use 24 for ground)
24 – Video signal input, RGBS, negative (ground)
25 – Video signal input, blue
26 – Video signal input, red

Connectors 6, aerial connectors


1 – AM and FM2 radio reception aerial connector, double Fakra, no coding, impedance 50 ohms, colour cream-white

2 – FM1 radio reception aerial connector, double Fakra, coding B, impedance 50 ohms, colour cream-white

3 – Navigation aerial connector, double Fakra, coding C, impedance 50 ohms, colour signal blue

[dream7000]

je to pre rns 510 ale hlavny konektor by mal byt taky isty, tu je pre RNS310

1. Multi-pin connector 1, 8-pin, for loudspeaker outputs
1 – Rear right loudspeaker, positive
2 – Front right loudspeaker, positive
3 – Front left loudspeaker, positive
4 – Rear left loudspeaker, positive
5 – Rear right loudspeaker, negative
6 – Front right loudspeaker, negative
7 – Front left loudspeaker, negative
8 – Rear left loudspeaker, negative

2. Multi-pin connector 2, 8-pin, for voltage supply lines and CAN bus
9 – CAN bus, high
10 – CAN bus, low
11 – Display voltage supply, positive
12 – Voltage supply, negative, terminal 31
13 – Display HV CAN bus low
14 – Display HV CAN bus high
15 – Voltage supply, positive, terminal 30
16 – Anti-theft coding control signal, SAFE, positive

3. Multi-pin connector 3, 12-pin, for telephone and microphone signals
1 – Microphone input, negative
2 – AUX output, audio, right
3 – AUX output, common signal earth
4 – Microphone output, negative
5 – Telephone audio input signal left, negative
6 – Telephone audio input signal right, negative
7 – Microphone input, positive
8 – AUX output, audio, left
9 – Microphone output, positive
10 – Telephone mute (mute switch for radio)
11 – Telephone audio input signal left, positive
12 – Telephone audio input signal right, positive

4. Multi-pin connector 4, 12-pin, for CD changer control and CD audio input signals
1 – AUX signal input, left
2 – AUX signal earth
3 – CD changer, audio signal earth
4 – CD changer, voltage supply, positive, terminal 30, contact continuous load greater than 1 A, temporary peak load 5 A
5 – Not assigned
6 – CD changer, DATA OUT
7 – AUX signal input, right
8 – CD changer, left audio channel, CD/L
9 – CD changer, right audio channel, CD/R
10 – CD changer, control line, switched positive
11 – CD changer, DATA IN
12 – CD changer, CLOCK (internal check protocol for data flow monitoring)

5. Navigation Aerial Connector
Navigation aerial connector (GPS), double Fakra, coding C, impedance 50 ohms, colour signal blue

6. FM 2 Aerial Connector
FM 2 radio reception aerial connector, double Fakra, coding B, impedance 50 ohms, colour cream-white

7. AM and FM Aerial Connector
AM and FM radio reception aerial connector, double Fakra, no coding, impedance 50 ohms, colour cream-white

[jan.fort]

Tak uz to maka, tak jak ma
dream7000 moc dekuju za schema....

[dream7000]

ahoj NZ hlavne ze je to OK.....

[George88]

ahoj, nevite nahodou nekdo jak mam pripojit zesilovac kablikem REMOTE, aby se mi zapinal s radiem. nevim na co to mam u tohoto radia zapojit. zkousel jsem antenu a ta to nesepne

[tornado1]

tohle radio nemá výstup na zesilovač..

[dream7000]

asi myslel ci na konektore radia najde spinaný +12V, kde sa objaví až po zapnutí radia....a ten zopne zosik.....